# Mounting the Arms

![You will need 16 - 30mm screws, 16 rubber tubes and 16 locking nuts. ](https://3973820583-files.gitbook.io/~/files/v0/b/gitbook-legacy-files/o/assets%2F-MJbvo5sx4tfu58g3Pne%2F-MLnJLcH276T53846Fs9%2F-MLnJoc5STE6hj-S3PK1%2FIMG_8125-2.JPG?alt=media\&token=6f717f71-26ed-44ac-9a93-b250b3838bfe)

![](https://3973820583-files.gitbook.io/~/files/v0/b/gitbook-legacy-files/o/assets%2F-MJbvo5sx4tfu58g3Pne%2F-MLnJLcH276T53846Fs9%2F-MLnNyrbmZy8bXuiGUJ1%2FScreen%20Shot%202020-11-10%20at%2012.20.45%20PM.png?alt=media\&token=d58bd1f1-cd7c-4d3e-95b8-46729f82ab7c)

Push the 30mm screws through the holes in the top plates as shown above. 

![](https://3973820583-files.gitbook.io/~/files/v0/b/gitbook-legacy-files/o/assets%2F-MJbvo5sx4tfu58g3Pne%2F-MLnJLcH276T53846Fs9%2F-MLnQaKRMm5QOIcS1NW-%2FIMG_8238.JPG?alt=media\&token=917e71e9-0b32-4697-a9f8-20bc077854be)

![](https://3973820583-files.gitbook.io/~/files/v0/b/gitbook-legacy-files/o/assets%2F-MJbvo5sx4tfu58g3Pne%2F-MLnJLcH276T53846Fs9%2F-MLnQLiSY1HVIzfDA54U%2FIMG_8234.JPG?alt=media\&token=a49c100c-5f2f-4d9a-9a69-2287fe9c58d9)

Do the same for all 16 screws. 

![](https://3973820583-files.gitbook.io/~/files/v0/b/gitbook-legacy-files/o/assets%2F-MJbvo5sx4tfu58g3Pne%2F-MLnJLcH276T53846Fs9%2F-MLnRMXJjKm9LLK71QBE%2FIMG_8133.JPG?alt=media\&token=2dcfce73-9aa2-42f1-89ad-c0962807932f)

lay the ESC wires and arm in the between the 4 holes on each hole  and then slide / push the upper plate on making sure the screws go all the way through the base plate. 

![](https://3973820583-files.gitbook.io/~/files/v0/b/gitbook-legacy-files/o/assets%2F-MJbvo5sx4tfu58g3Pne%2F-MLnJLcH276T53846Fs9%2F-MLnSj-xU0E0mX286N0S%2FIMG_8134.JPG?alt=media\&token=02811b84-5dbf-436d-a593-786fae9e4d63)

Once all 8 on the upper plate are in, push the arm all the way in until it stops against the 20mm standoff. Then tighten all of the screws. 

![](https://3973820583-files.gitbook.io/~/files/v0/b/gitbook-legacy-files/o/assets%2F-MJbvo5sx4tfu58g3Pne%2F-MLnJLcH276T53846Fs9%2F-MLnU7QBCtWdoc30UPdk%2FIMG_8139.JPG?alt=media\&token=033e91b1-cffd-4c88-b3a4-cc69a1e8dc6d)

Your Hawk  / Longbow should look like this once you mount the front and rear top plates. 

![](https://3973820583-files.gitbook.io/~/files/v0/b/gitbook-legacy-files/o/assets%2F-MJbvo5sx4tfu58g3Pne%2F-MLnJLcH276T53846Fs9%2F-MLnVaJ9Y4FDZ5CwVxll%2FIMG_8162-2.JPG?alt=media\&token=9af2324c-17de-4599-bd74-20d66a6ec798)

Recommend you use small zipties to secure the extra wires.