> For the complete documentation index, see [llms.txt](https://onpoynt-1.gitbook.io/the-hawk/llms.txt). Markdown versions of documentation pages are available by appending `.md` to page URLs; this page is available as [Markdown](https://onpoynt-1.gitbook.io/the-hawk/landing-gear-and-payload-plate.md).

# Landing Gear and Payload Plate

![](https://3973820583-files.gitbook.io/~/files/v0/b/gitbook-legacy-files/o/assets%2F-MJbvo5sx4tfu58g3Pne%2F-MLoL3BuF7CMv7y208JA%2F-MLoLPPDkbkeyVkChnNJ%2FIMG_8191.JPG?alt=media\&token=a63d89b5-9280-4aeb-8a1e-81730274c422)

The landing gear should be mounted so that the slanted  support point to the front of the drone. 

 

![](https://3973820583-files.gitbook.io/~/files/v0/b/gitbook-legacy-files/o/assets%2F-MJbvo5sx4tfu58g3Pne%2F-MLoL3BuF7CMv7y208JA%2F-MLoM4zNtitFrwMpmAbS%2FIMG_8193.JPG?alt=media\&token=49736b4a-0aa2-47e7-b3bb-9f1efd627681)

Push two 12mm screws through the landing gear mounts. 

![](https://3973820583-files.gitbook.io/~/files/v0/b/gitbook-legacy-files/o/assets%2F-MJbvo5sx4tfu58g3Pne%2F-MLoL3BuF7CMv7y208JA%2F-MLoM85LMkBCd0hUJJmO%2FIMG_8190.JPG?alt=media\&token=77055248-b65e-47d5-9843-33a215f733b4)

Align the gear plate so the screws come thru the slots.

![](https://3973820583-files.gitbook.io/~/files/v0/b/gitbook-legacy-files/o/assets%2F-MJbvo5sx4tfu58g3Pne%2F-MLoL3BuF7CMv7y208JA%2F-MLoMC-W58nvjD0tTo-B%2FIMG_8194.JPG?alt=media\&token=c2e2b117-9c2d-4186-987c-c4ae20df42af)

Use the locking nuts to secure the grear skids to the mount. 

![](https://3973820583-files.gitbook.io/~/files/v0/b/gitbook-legacy-files/o/assets%2F-MJbvo5sx4tfu58g3Pne%2F-MLoL3BuF7CMv7y208JA%2F-MLoMFIJBlWlg0QUB2nI%2FIMG_8196.JPG?alt=media\&token=8c75613e-6b21-4f1a-be86-342f3cf9216d)

You will need to use both the allen driver and either pliers or socket to tighten them.

![](https://3973820583-files.gitbook.io/~/files/v0/b/gitbook-legacy-files/o/assets%2F-MJbvo5sx4tfu58g3Pne%2F-MLoL3BuF7CMv7y208JA%2F-MLoMUksEVEhvNQx3Ljn%2FIMG_8198.JPG?alt=media\&token=4bc4f0a9-bf58-4856-aa25-e07fef7ccf91)

Mount the other side in the same manor. 

### Adding the Payload Platform

The payload plates for the Hawk and the Longbow are different sizes. 

Note: This platform / plate can be added during the build or later. It is not required to fly the drone but can provided additional surface area for batteries, a secondary processor (Raspberry Pi) or other payloads. 

![](https://3973820583-files.gitbook.io/~/files/v0/b/gitbook-legacy-files/o/assets%2F-MJbvo5sx4tfu58g3Pne%2F-MLoL3BuF7CMv7y208JA%2F-MLoOetCvvw4Hq_4_v_y%2FIMG_8199.JPG?alt=media\&token=b0ac3ca6-9ffc-462f-91c7-f437071e274a)

![](https://3973820583-files.gitbook.io/~/files/v0/b/gitbook-legacy-files/o/assets%2F-MJbvo5sx4tfu58g3Pne%2F-MLoOkThFJ-Rd8q6Ydxa%2F-MLoQXwWkqZBLq7G9bVz%2FIMG_8273.JPG?alt=media\&token=811af8d7-801f-4c98-a995-9a762bf73672)

Push 8mm or 12mm screws from the inside of the drone and secure with 35mm standoffs.  

![](https://3973820583-files.gitbook.io/~/files/v0/b/gitbook-legacy-files/o/assets%2F-MJbvo5sx4tfu58g3Pne%2F-MLoOkThFJ-Rd8q6Ydxa%2F-MLoRUM80zZVqma0dtPs%2FIMG_8200.JPG?alt=media\&token=21bcb779-719d-489e-9270-18b9fc37ede7)

Secure the payload plate with 8mm screws. 

![](https://3973820583-files.gitbook.io/~/files/v0/b/gitbook-legacy-files/o/assets%2F-MJbvo5sx4tfu58g3Pne%2F-MLoOkThFJ-Rd8q6Ydxa%2F-MLoRsUgo_Jb6Z7ey9DI%2FIMG_8203.JPG?alt=media\&token=bd07f569-bbae-4402-b321-49b9954fa83d)